Aircraft Tiedowns

P/N: 3197 NAME: Aircraft Tie-Down Bracket PRICE: $117.50 / Each ELIGIBLE ON: PA-12, PA-18 Series Aircraft STC's: - PA-12: SA02067AK - PA-18: SA02066AK FAA-PMA'd: Yes WEIGHT: 15 OZ. Each MATERIAL: Stainless Steel W/ Aluminum Spacers PURPOSE: - To remove the tie down load from the front lift strut U-channel that is attached to the front spar. INSTALLATION: This modification is recommended at the time of wing covering. MISC INFO:...
More

Axle Adapter Kit

  P/N: 2079 NAME: Axle Adapter Kit PRICE: $185.00 ELIGIBLE ON: Aircraft using 1 1/4'' axles STC's: No FAA-PMA'd: No WEIGHT: 1.1 Lbs. For both (Kit Weight) MATERIAL: - 4130N - Washers are stainless steel. PURPOSE: - Converts 1 1/4'' axle to 1 1/2'' axle. - Originally designed for ski use. - Can be adapted for wheel use. INSTALLATION: - No special tools needed to install. - No welding required. - Bearing stops & axle ada...
More

Belly Pan Clean Out Kit

P/N: 3285 NAME: Belly Pan Clean Out Kit PRICE: $285.00 ELIGIBLE ON: PA-18 STC's: No FAA-PMA'd: Yes WEIGHT: 1.8 Lbs. MATERIAL: - 2024-T3 Aluminum pan - Mild steel receptacle plates PURPOSE: - To allow clean out of AFT, lower fuselage section and to gain access to jack screw & pulleys. INSTALLATION: - Normally installed at time of rebuild - Welding is required for loin fastener receptacle plates. MISC INFO:
More

Cabane

P/N: 3166-2 NAME: CABANE for PA-12 & PA-14 PRICE: $365.00 STC's: YES FAA-PMA'd: YES MISC INFO: - ELIGIBLE ON PA-12, -14 IF PA-18 TYPE IF MAIN LANDING GEAR FITTINGS HAVE BEEN INSTALLED IN ACCORDANCE WITH STC#  SA148AL, SA669AL. ONCE THIS IS ACCOMPLISHED, AN ADDITIONAL WELD ON FITTING KIT WILL BE NEEDED FOR INSTALLATION OF THE CABANE   P/N: 3166-1 NAME: CABANE for PA-18 PRICE: $285.00 STC's: YES FAA-PMA'd: ...
More

Carb Air Filter Dome

P/N: 3281 NAME: Carb Air Filter Dome PRICE: $122.50 ELIGIBLE ON: PA-18/150HP Aircraft STC's: No FAA-PMA'd: Yes WEIGHT: 5 Oz. MATERIAL: - Aluminum - Powder coated white or flat black PURPOSE: INSTALLATION: Same as stock air filter dome MISC INFO: - INCLUDED: Stainless steel doubler to install over mount hole to prevent wear and tear. - Direct replacement for P/N: 15007-00  
More

Carb Heat Box

P/N: AD15005-00 - Direct replacement for P/N: 15005-00 NAME: Carb Heat Box PRICE: $1085.00 ELIGIBLE ON: PA18-150HP STC's: No FAA-PMA'd: Yes WEIGHT: N/A MATERIAL: 304 Stainless Steel PURPOSE: - Has self lubricating bearings for longer service life - Stainless material to help prevent from corrosion & rust. INSTALLATION: Direct replacement for - P/N 15005-00 MISC INFO:
More

Carbon Fiber Straight Ski (Pair)

P/N: F.A.DODGEX-1 NAME: Carbon Fiber Straight Ski PRICE: 5450.00 / Pair includes rigging ELIGIBLE ON: Approval pending STC's: Yes FAA-PMA'd: TSO'D WEIGHT: Approximately 35 Lbs Per ski with rigging MATERIAL: - 4130N Steel, Pedestal powder coated flat black - Ski board is carbon fiber - Ski bottom is UHMW PURPOSE: - New high performance designed ski - Excellent flotation and fast turning INSTALLATION: - Same as any direct replacemen...
More

Cargo Tie Down Base Plates

P/N: 40000-11 NAME: Cargo Tie Down Ring Base Plate PRICE: $15.00 / Each (Net) ELIGIBLE ON: N/A STC's: No FAA-PMA'd: No WEIGHT: 1 Oz. MATERIAL: 7075-TG511 Aluminum Anodized Black Or Blue *Color depending on production run* PURPOSE: - A receptacle for p/n 40340-20 cargo tie down ring - Load rating - 2000 Lbs. INSTALLATION: - HIGHLY RECOMMENDED TO USE MS24694 STRUCTURAL SCREWS WITH DOUBLERS BEHIND MOUNTING SURFACE - Please consult AC-4...
More

Cargo Tie Downs Rings

  P/N: 40340-20 - DIRECT REPLACEMENT FOR P/N: 07110069-1, -2, -5, -6 NAME: CARGO TIE DOWN RINGS PRICE: $15.00 / Each Net ELIGIBLE ON: N/A STC's: NO FAA-PMA'd: NO WEIGHT: 2.5 OZ. MATERIAL: STEEL PURPOSE: - PROVIDES TIE DOWN CAPABILITIES TO SECURE CARGO - LOAD RATING: VERTICAL LOAD - 4000 LBS HORIZONTAL LOAD - 2000 LBS 45 DEGREE LOAD - 3000 LBS. INSTALLATION: CONSULT AC-43.13-2B CHAPTER 12 FOR INSTALLATION PRACTICES M...
More

Clamp On Headset Hanger Bracket

P/N: AD-18-HSH NAME: Clamp on headset hanger bracket PRICE: $28.50 / Each ELIGIBLE ON: PA-18 Aircraft STC's: N/A FAA-PMA'd: N/A WEIGHT: 2 Oz MATERIAL: - Steel  - Powder coated flat black PURPOSE: -To hang up headsets in cockpit INSTALLATION: - This will clamp on the top deck X-brace.  - Clamp is for 7/8'' Dia tube.  - When installing hanger post must be facing away from pilot or passanger MISC INFO: - Custom fabrication of ...
More

Cowl Channels, LOWER (SS and Titanium)

P/N: 3277 NAME: LOWER COWL CHANNEL (STAINLESS STEEL) PRICE: $88.50 / Each ELIGIBLE ON: PA-18 SERIES AIRCRAFT STC's: NO FAA-PMA'd: YES WEIGHT: 9 OZ. MATERIAL: STAINLESS STEEL w/ STAINLESS STEEL FASTENERS PURPOSE: - WILL NOT RUST OUT - DOUBLERS AT EACH END TO PREVENT WEAR AND CRACKING OUT AT FASTENER HOLES INSTALLATION: SAME AS STOCK COWL CHANNEL MISC INFO: - COWL CHANNELS DO NOT HAVE FASTENER HOLES IN ENDS, THIS AIDS ...
More

Cowl Channels, UPPER (SS and Titanium)

P/N: 3276 NAME: UPPER COWL CHANNEL PRICE: $88.50 / Each ELIGIBLE ON: PA-18 SERIES AIRCRAFT STC's: NO FAA-PMA'd: YES WEIGHT: 8 OZ. MATERIAL: STAINLESS STEEL w/ STAINLESS STEEL FASTENERS PURPOSE: - WILL NOT RUST OUT - DOUBERLS AT EACH END TO PREVENT WEAR AND CRACKING OUT AT FASTENER HOLES INSTALLATION: SAME AS STOCK COWL CHANNEL MISC INFO: - COWL CHANNELS DO NOT HAVE FASTENER HOLES IN ENDS, THIS AIDS THE INSTALLER TO A...
More

Engine Mount

  P/N: U12351-015 NAME: Engine Mount PRICE: $785.00 ELIGIBLE ON: PA18-150HP Aircraft STC's: No FAA-PMA'd: Yes WEIGHT: Same as original MATERIAL: 4130N Steel PURPOSE: To secure the power plant to firewall of aircraft. INSTALLATION: Same as stock Piper Installation MISC INFO: - Mount is powder coated gloss black with ground tabs installed under request - Custom colors are available
More

Extended Baggage Kit

Extended Baggage Installation.pdf P/N: 2103 NAME: Extended Baggage PRICE: $785.00 ELIGIBLE ON: PA-18 Aircraft STC's: Yes, SA590AL FAA-PMA'd: Yes WEIGHT: 7 Lbs. MATERIAL: .020 2024-T3 Aluminum PURPOSE: Allows Aircraft Owner To Have More Usable Baggage INSTALLATION: - No Welding Required - The Baggage Compartment Is Shipped In A Knock Down Configurations - Can Be Assembled Using Blind Rivets Or Solid Rivets, See Attached Instruction...
More

Fuel Cap for 180HP Piper

  P/N: 3267-180 NAME: Fuel Cap for 180HP Piper PRICE: $87.50 ELIGIBLE ON: -12, -14, -18 Series aircraft STC's: No FAA-PMA'd: No WEIGHT: 3 Oz. MATERIAL: Stainless steel PURPOSE: Designes to comply with STC's using 180HP enigne on PA-12, PA-14 & PA-18 Aircraft INSTALLATION: Same as stock cap MISC INFO: - Vent tube must face forward on aircraft - May interfere with installing wing covers on aircraft. ...
More

Fuel Cap, Vented

P/N: 3267 NAME: Fuel Cap, Vented PRICE: $72.50 / Each ELIGIBLE ON: See AML3267, Dated 09-07-95 STC's: SA02040AK FAA-PMA'd: Yes WEIGHT: 3 Oz. MATERIAL: Stainless steel with high quality gasket PURPOSE: - Stainless steel fuel cap will not rust out. - Easy removal and replacement. INSTALLATION: Same as stock fuel cap. MISC INFO: - Has fin on top of each cap that helps facilitate installation and removal procedures. - No service...
More

Fuel System Sight Gauge

FUEL SYSTEM SIGHT GAUGE, MANDATORY SERVICE BULLETIN.pdf P/N: 3286 NAME: FUEL SYSTEM SIGHT GAUGE PRICE: $62.50 / Each ELIGIBLE ON: PA-12, PA-14, PA-18 SERIES AIRCRAFT USING ATLEE DODGE 30.5 GAL FUEL TANKS ONLY STC's: SA02115AK FAA-PMA'd: YES WEIGHT: 2 OZ MATERIAL: TYGOTHANE TUBING w/ ALUMINUM RESTRICTORS PURPOSE: ELIMINATES ELECTRICAL GAUGES INSTALLATION: - MUST USE INSTALLATION INSTRUCTIONS AND CALIBRATION PROCEDURES INCLUDED WITH ...
More

Fuel Tank, 30.5 Gallon

P/N: 3140-L, 3140-R NAME: 30.5 GAL FUEL TANK FOR PA-18 PRICE: $3125.00 / Each STC's: YES FAA-PMA'd: YES MISC INFO:   P/N: 3140-516-L, 3140-516-R NAME: 30.5 GAL FUEL TANK FOR PA-12 & PA-14 PRICE: $3125.00 / Each STC's: YES FAA-PMA'd: YES MISC INFO:   P/N: 3258-L, 3258-R NAME: 30.5 GAL FUEL TANK FOR PA-22 PRICE: $3125.00 / Each STC's: YES FAA-PMA'd: YES ...
More

Header Tank, FRONT

P/N: 3169-1 NAME: FRONT HEADER TANK PRICE: $285.00 ELIGIBLE ON: PA-18 STC's: SA2303NM FAA-PMA'd: YES WEIGHT: 12.5 OZ. MATERIAL: ALUMINUM, LIGHTWEIGHT & HEAVY DUTY DESIGN PURPOSE: WEIGHT SAVING IS APPROXIMATELY 9 OZ. INSTALLATION: SAME AS STOCK HEADER TANK MISC INFO: - DIMENSIONS: 16''l x 3''od. - DIRECT REPLACEMENT FOR PIPER HEADER TANKS - NO SERVICE BULLETINS OR AD NOTES AGAINST THE TANKS - TANK HAS (1) 1/8 NPT AND (1) ...
More

Header Tank, REAR

P/N: 3169-2 NAME: REAR HEADER TANK PRICE: $285.00 ELIGIBLE ON: PA-18 STC's: SA2303NM FAA-PMA'd: YES WEIGHT: 13.0 OZ. MATERIAL: ALUMINUM, LIGHTWEIGHT & HEAVY DUTY DESIGN PURPOSE: WEIGHT SAVINGS APPROXIMATELY 9 OZ. INSTALLATION: SAME AS STOCK HEADER TANK MISC INFO: - DIMENSIONS: 15''l x 3''od. - DIRECT REPLACEMENT FOR PIPER HEADER TANKS - NO SERVICE BULLETINS OR AD NOTES AGAINST THE TANKS - TANK HAS (1) 1/4 BEADED TUBE AND...
More

Heavy Duty Brake Reinforcing Channel

  P/N: 4231 Direct replacement for P/N 12944-00 NAME: Heavy Duty Brake Reinforcing Channel PRICE: $85.00 ELIGIBLE ON: PA-18 Series Aircraft STC's: No FAA-PMA'd: Yes WEIGHT: 0.7 Lbs. MATERIAL: - 4130N Steel - Powder coated grey PURPOSE: - This brake channel is stronger than the piper original channel and is not prone to cracking out INSTALLATION: - Same installation as stock piper channel - Normally installed during an airc...
More

Heavy Duty Refueling Step

P/N: 3190-12-SKI NAME: Heavy Duty Refueling Step PRICE: $127.50 ELIGIBLE ON: PA-18 Style landing gear STC's: Pending FAA-PMA'd: Pending WEIGHT:  13 Oz. MATERIAL:  4130N Steel, powder coated white or black INSTALLATION:  Clamps on front main landing gear tube. MISC INFO:  Before placing order measure the outside diameter of the front landing gear tube.  
More

Installation of PA-18 Cathedral Ceilings, STC ONLY

[PDF] STC SA02419AK, Reference Use Only.pdf P/N: STC Only NAME: Installation of PA-18 Cathedral ceilings PRICE: $245.00 / STC Only ELIGIBLE ON: Piper PA-18, PA-12S SERIES AIRCRAFT STC's: SA02419AK FAA-PMA'd: N/A WEIGHT: N/A MATERIAL: 4130N PURPOSE: To remove diagonal tube aft of rear spar carry through. This modification allows easier access for loading and unloading cargo aft of rear seat. INSTALLATION: This modification should b...
More

Installation of PA-18 Front Seat, STC Only

STC SA02418AK, Reference Use Only.pdf P/N: STC Only NAME: Installation of PA-18 Front Seat PRICE: $545.00 / STC Only ELIGIBLE ON: Piper PA-12, PA-12S Series Aircraft STC's: SA02418AK FAA-PMA'd: N/A WEIGHT: N/A MATERIAL: 4130N PURPOSE: This modification allows the installation of a Piper PA-18 front seat, that is adjustable and superior in strength. INSTALLATION: This installation can be welded in or a clamp in/weld in modification...
More

Instrument Panels

P/N: 1034 NAME: PA-12 INSTRUMENT PANEL PRICE: $375.00/ Each STC's: YES FAA-PMA'd: NO MISC INFO: - CUSTOM ORDER - ENLARGED REMOVABLE & ENLARGED FIXED   P/N: 1034-1 NAME: PA-18 INSTRUMENT PANEL PRICE: $375.00 / Each STC's: YES FAA-PMA'd: NO MISC INFO: - CUSTOM ORDER - ENLARGED REMOVABLE & ENLARGED FIXED   P/N: 1034-2 NAME: PA-14 INSTRUMENT PANEL PRICE: $425.00 / Ea...
More

Lift Strut Reinforcement Bracket

P/N: 3192-12, 3192-18 NAME: LIFT STRUT REINFORCEMENT BRACKET PRICE: $72.50 EACH ELIGIBLE ON: PA-12, PA-18 SERIES AIRCRAFT STC's: - PA-12, -14: SA02021AK - PA-18: SA02026AK FAA-PMA'd: YES WEIGHT: 4 OZ. EACH MATERIAL: - 4130N STEEL - POWDER COATED WHITE PURPOSE: TO REINFORCE U-CHANNEL ON FRONT SPAR LIFT STRUT ATTACHMENT. INSTALLATION: - CAN BE ACCOMPLISHED WHEN WINGS ARE COVERED - INSTALL TIME WITH FABRIC ON WINGS IS 1.5 HOURS PER S...
More

Lifting Eyes

P/N: 3217 NAME: LIFTING EYES PRICE: $77.50 / Pair ELIGIBLE ON: CALL FOR INFORMATION STC's: NO FAA-PMA'd: NO WEIGHT: 3 OZ. MATERIAL: 304 STAINLESS STEEL PURPOSE: TO ENABLE AIRCRAFT TO BE LIFTED INSTALLATION: - MOUNTS TO 1st AN-6 BOLT OUTBOARD OF WING ATTACH BOLT - ON STOCK PIPER WINGS, BOLT SHOULD BE LONG ENOUGH TO ACCEPT LIFTING EYES - LEADING EDGE WING FAIRING WILL NEED A SLOT CUT IN IT TO ACCEPT LIFTING EYES. MISC INFO: NOR...
More

Long Step

P/N: 3195 NAME: LONG STEP PRICE: $185.00 ELIGIBLE ON: J-3 THRU PA-18 SERIES AIRCRAFT STC's: SA02007AK FAA-PMA'd: YES WEIGHT: 3 LBS MATERIAL: - 6061-T6 ALUMINUM - POWDER COATED WHITE OR BLACK PURPOSE: - TO ASSIST IN REFUELING, CLIMBING IN & OUT OF THE AIRCRAFT - NORMALLY INSTALLED ON THE RIGHT SIDE OF THE AIRCRAFT. INSTALLATION: - CLAMP ON MODIFICATION - WHEN ORDERING IT'S RECOMMENDED ON MEASURING THE OUTSIDE DIAMETER OF THE F...
More

Lumber Rack

Lumber Rack Installation for PA-18.pdf P/N: 12-LR, 18-LR NAME: Lumber Rack PRICE: $575.00 ELIGIBLE ON: Will fit -12, -14, -18 style aircraft STC's: No FAA-PMA'd: No WEIGHT: 19.9 Lbs without load MATERIAL: - Mild Steel - 4130N Steel - Powder coated Call for Colors PURPOSE: To have external loads - Building materials & a wide range of items. INSTALLATION: Clamps to the lower longeron in 3 places on each side of the aircraft. ...
More

Main Landing Gear, 1 1/2” Axle , 3” Extended

[PDF] 20130222_134806_MLG SERVICE BULLETIN, MARCH-15-2005.pdf P/N: 3284-1A (LH), 3284-2A (RH) NAME: 1 1/2'' Axle Main Landing Gear 3'' Extended PRICE: $485.00 / Per Side ELIGIBLE ON: PA-12 , PA-14, WITH PA18 STYLE GEAR STC PA-18 Series aircraft STC's: - PA-12, PA-14:  SA02188AK - PA-18:   SA02152AK FAA-PMA'd: Yes WEIGHT: 8.7 Lbs. Per side MATERIAL: - 4130N Steel - Comes bare but can be powder coated white, black or, primer grey for an addi...
More

Main Landing Gear, 1 1/2” Axle, STD

20130222_134806_MLG SERVICE BULLETIN, MARCH-15-2005.pdf P/N: 3284-1A (LH), 3284-2A (RH) NAME: 1 1/2'' AXLE MAIN LANDING GEAR, 3'' EXTENDED PRICE: $485.00 / Per Side ELIGIBLE ON: PA-12, PA-14, PA-18 SERIES AIRCRAFT STC's: - PA-12, PA-14:  SA02188AK - PA-18:   SA02152AK FAA-PMA'd: YES WEIGHT: 8.7 LBS. PER SIDE MATERIAL: - 4130N STEEL - NORMALLY COMES BARE BUT CAN BE POWDER COATED FOR $70.00 PER SIDE PURPOSE: - GEAR IS HEAVY DUTY DESIGNED ...
More

Main Landing Gear, 1 1/4” Axle, 3” Extended

  [PDF] 20130222_134744_MLG SERVICE BULLETIN, MARCH-15-2005.pdf P/N: 3284-1 (LH), 3284-2 (RH) NAME: 1 1/4'' AXLE MAIN LANDING GEAR, 3'' EXTENDED PRICE: $485.00 / Per Side ELIGIBLE ON: PA-12, PA-14, PA18 SERIES AIRCRAFT STC's: - PA-12, PA-14:  SA02188AK - PA-18:  SA02152AK FAA-PMA'd: YES WEIGHT: 8.7 LBS. PER SIDE MATERIAL: - 4130N STEEL TUBING - NORMALLY COMES WITH NO PRIMER BUT CAN BE POWDER COATED FOR $70.00 PER SIDE PURPOSE: -...
More

Main Landing Gear, 1 1/4” Axle, STD

MLG SERVICE BULLETIN, MARCH-15-2005.pdf P/N: 3225-1 (LH), 3225-2 (RH) NAME: 1 1/4'' Axle Main Landing Gear, Standard PRICE: $465.00 / Per Side ELIGIBLE ON: J-3, PA-11, PA-18, PA-19 Series aircraft STC's: No FAA-PMA'd: Yes WEIGHT: 8.4 Lbs. Per gear MATERIAL: - 4130N Steel tubing - Comes bare, but can be powder coated white, black or, primer grey for 70.00 per side. (Custom colors available, call for more information) PURPOSE: - Gear is he...
More

Muffler Shroud – 2 Piece Split

P/N: 3236 - DIRECT REPLACEMENT FOR P/N: 12436-10 & 71261-08 NAME: MUFFLER SHROUD-2 PIECE SPLIT PRICE: $385.00 ELIGIBLE ON: PA-18/150 HP AIRCRAFT STC's: SA02024AK FAA-PMA'd: YES WEIGHT: 1.9 LBS. - NO WEIGHT CHANGE MATERIAL: 5052-H32 & 6061-T6 ALUMINUM PURPOSE: SHROUD IS EASIER TO REMOVE AND INSTALL ON MUFFLER THAN STOCK PIPER SHROUD. INSTALLATION: NORMALLY ACCOMPLISHED DURING MUFFLER INSPECTIONS. MISC INFO: - SHROUD I...
More

PA-18 Folding Seat Kit

P/N: 3186 NAME: PA-18 Folding Seat Kit PRICE: - $385.00 - $845.00 Installed on Customers Seat ELIGIBLE ON: PA-18 Folding Seat Kit STC's: SA02085AK FAA-PMA'd: Yes WEIGHT: 1 Lbs. MATERIAL: 4130N Steel PURPOSE: - To allow the pilot seat back to fold forward for ease of passenger egress & ease of loading baggage/cargo INSTALLATION: - Welding is required - Installation time of the kit onto seat is 2-4 hours depending on welders back...
More

PA-18 Heavy Duty Muffler

P/N: 3241- HEAVY DUTY DIRECT REPLACEMENT FOR P/N: 12433-14 NAME: PA-18 HEAVY DUTY MUFFLER PRICE: $785.00 ELIGIBLE ON: PA-18 STC's: SA02023AK FAA-PMA'd: YES WEIGHT: 6.2 LBS MATERIAL: 321 STAINLESS STEEL WITH TAILPIPE GUSSETS AND BALE PURPOSE: - THIS MUFFLER ELIMINATES THE AD 68-05-01. WHEN MUFFLER IS PURCHASED, THE STC PAPERWORK INCLUDES A FAA LETTER STATING THAT THE INSTALLATION OF THIS MUFFLER IS AN ALTERNATIVE MEANS OF COMPLIANCE TO TH...
More

PA-18 Hot Rod Muffler

P/N: 3241-HR NAME: PA-18 Hot Rod Muffler PRICE: $1,425.00 STC's: Yes FAA-PMA'd: Yes MISC INFO: - Average RPM increase is 30-65 RPM - Most aircraft have a slight rate of climb increase. - EGT Slightly lower - Oil temp slightly lower - No modifications to cowling or stacks are needed - FAA direst replacement - NO A.D. NOTE MUFFLER COMES WITH FAA LETTER STATING MUFFLER IS AN ALTERNATIVE MEANS OF COMPLIANCE TO THE A.D. - Sound slightly louder/deeper - ...
More

PA-18 Stainless Steel Firewall

P/N: 8007-01 NAME: Stainless Steel Firewall PRICE: $465.00 ELIGIBLE ON: PA-18 Series aircraft STC's: No FAA-PMA'd: Yes WEIGHT: 4 Lbs. 10 OZ. MATERIAL: Stainless Steel PURPOSE: - Clean smooth stainless steel finish will not corrode out like original galvanized Piper firewalls. INSTALLATION: Same as stock Piper firewall. MISC INFO: - When ordering our facility can eliminate hole as per customer request. - PA-12 FIREWALLS: Cus...
More

PA-18 Titanium Firewall

P/N: 8007-02 NAME: Titanium Firewall PRICE: $645.00 ELIGIBLE ON: PA-18 Series Aircraft STC's: No FAA-PMA'd: Yes WEIGHT: 2 Lbs. 6 Oz. MATERIAL: Titanium PURPOSE: Weight savings modification INSTALLATION: Same as stock Piper firewall MISC INFO: - When ordering our facility can eliminate holes as per customer request - PA-12 FIREWALLS: Custom made as per customer request, not FAA-PMA'd - Direct replacement for P/N: 12365-003...
More

Pilot’s Safety Barrier Net

P/N: 3234 NAME: PILOT'S SAFETY BARRIER NET. Available in BLACK only. PRICE: STC:$385.00 Parts Kit and Net: $785.00 ELIGIBLE ON: J3, PA-12, PA-14, PA-18 AIRCRAFT STC's: SA02452AK FAA-PMA'd: Yes WEIGHT: approx 4 LBS. MATERIAL: - CLAMP IN BRACKETS: 4130N STEEL, POWDER COATED FLAT BLACK - WELD IN BRACKETS: 4130N STEEL, NO PAINT - NET IS BLACK IN COLOR USING 1'' WEBBING PURPOSE: - TO PREVENT CARGO FROM MOVING FORWARD IN CASE OF HEAVY TURBU...
More

Pilot’s Seat Bottom Access Panel

Pilot's Seat Bottom Access Panel," P/N: 3186-SLB NAME: PILOT'S SEAT BOTTOM ACCESS PANEL PRICE: $82.50 ELIGIBLE ON: AIRCRAFT USING PA-18 SEAT STC's: NO FAA-PMA'd: NO WEIGHT: 0.8 LBS. MATERIAL: - ALUMINUM - POWDER COATED FLAT BLACK PURPOSE: SEAT BOTTOM LID TO ACCESS UNDER SEAT BATTERY INSTALLATION: REQUIRES DRILLING, RIVETING MISC INFO: KIT COMES WITH HINGE AND RIVETS
More

Preheat Shroud 2 Piece Split

P/N: 3182 NAME: PREHEAT SHROUD - 2 PIECE SPLIT PRICE: $245.00 ELIGIBLE ON: PA-18 SERIES AIRCRAFT STC's: SA02025AK FAA-PMA'd: YES WEIGHT: 12.5 OZ MATERIAL: 5052 ALUMINUM, 6061-T6 ALUMINUM PURPOSE: - SHROUD IS DESIGNED TO REMOVE & INSTALL VERY EASILY, USING 2 STAINLESS STEEL HOSE CLAMPS TO SECURE. INSTALLATION: SAME AS STOCK SHROUD INSTALLATION REQUIREMENTS. MISC INFO:
More

Rear Seat Heater Kit

P/N: 3175 NAME: REAR SEAT HEATER KIT PRICE: $685.00 ELIGIBLE ON: PA-18 AIRCRAFT EQUIPPED WITH LYCOMING ENGINES. STC's: SA02094AK FAA-PMA'd: YES WEIGHT: 2.4 LBS. MATERIAL: - STAINLESS STEEL DIVERTER BOX & PUSH PULL CABLES - HOSES ARE 2'' CEET& 2'' SCAT PURPOSE: - CARBURETOR HEAT IS UTILIZED AND USES NEW STAINLESS STEEL DIVERTER BOX & SYSTEM TO PROVIDE AIRCRAFT WITH REAR SEAT HEAT INSTALLATION: - APPROXIMATELY 8 HOURS FOR...
More

Rear Stick Cover

  P/N: 3343 NAME: Rear Stick Cover PRICE: $335.00 ELIGIBLE ON: Will fit -3, -5, -11, -12, -18 Series aircraft STC's: No FAA-PMA'd: No WEIGHT: 1.2 LBS MATERIAL: Poly high impact plastic PURPOSE: - Prevents foreign objects from falling on rear stick stub when rear stick is removed. INSTALLATION: - Refer to installation instructions included with purchase of stick cover. - Drilling is required. - Stick cover can be installaed w...
More

Refueling Step

P/N: - 3190-10, for 1 1/4"" Tube - 3190-11, for 1 3/8"" Tube - 3190-12, for 1 1/2"" Tube NAME: REFUELING STEP PRICE: $85.00 / Each ELIGIBLE ON: J-3 thru PA-20 SERIES AIRCRAFT STC's: - PA-12: SA2346NM, SA2347NM, SA2348NM, SA3602NM - PA-14: SA3603NM - PA-18: SA3606NM - PA-20: SA3607NM - PA-22: SA3608NM FAA-PMA'd: YES WEIGHT: 8 OZ MATERIAL: - 4130N STEEL - POWDER COATED WHITE OR BLACK PURPOSE: TO ASSIST IN REFUELING AIRCRAFT INSTA...
More

Remote Compass Mounting Bracket

P/N: 1033 NAME: REMOTE COMPASS MOUNTING BRACKET PRICE: $175.00 / Each ELIGIBLE ON: J-3 thru PA-22 STC's: SA144AL FAA-PMA'd: YES WEIGHT: APPROXIMATELY 3lbs @ 10.5'' AFT OF WING LEADING EDGE WITH TRANSMITTER MATERIAL: 2024-T3 ALUMINUM PURPOSE: TO ELIMINATE COMPASS DEVIATIONS INSTALLATION: - ATTACHED TO THE AFT SIDE OF THE FRONT SPAR LH OR RH AT APPROXIMATELY 140.5'' OUTBOARD FROM #1 INBOARD RIB- BE SURE THE CABLE IS LONG ENOUGH TO...
More

Removable Rear Seat Crossbar

P/N: 3146 NAME: REMOVABLE REAR SEAT CROSSBAR PRICE: $285.00 ELIGIBLE ON: PA-18 SERIES AIRCRAFT STC's: SA681AL FAA-PMA'd: YES WEIGHT: 15 OZ. MATERIAL: 4130N SQUARE TUBING PURPOSE: - ALLOWS AIRCRAFT OPERATOR TO REMOVE REAR SEAT CROSSBAR TO LOAD AND UNLOAD BAGGAGE/CARGO. INSTALLATION: - NO WELDING REQUIRED - INSTALL TIME IS ABOUT 30 MINUTES. MISC INFO: - THIS CROSSBAR MUST BE INSTALLED PRIOR TO FLIGHT. IF NOT INSTALLED, SERIOUS...
More

Safari Seat

P/N: 6151 NAME: Safari Seat PRICE: $635.00 ELIGIBLE ON: PA-18 Series Aircraft STC's: SA02356AK-D FAA-PMA'd: Yes WEIGHT: 6.4 Lbs. MATERIAL: - Lightweight 4130N steel - Powder coated flat black PURPOSE: Saves apprpximately 14 Lbs. when removing stock seat configuration INSTALLATION: No welding required, clamp in configuration MISC INFO: - Seat bottom: 13.5'' wide - Seat back: 11.5'' wide - No upholstery included - Seat back o...
More

Safety Cables for MLG, 3” Extended

The landing gear safety cable kit consists of two upper safety cable assemblies and one lower assembly.  Each of the two upper assemblies are identical and have steel attach links on both ends.  The lower assembly has an attachment plate secured to the upper ends of the left and right cables and an attachment link secured to the lower ends of the left and right cables. P/N: 3344-12 (PA-12, PA-14), 3344-18 (PA-18) NAME: Main Landing Gear Safety Cables, 3'' Extended PRICE: $1...
More

Safety Cables for MLG, STD

  The landing gear safety cable kit consists of two upper safety cable assemblies and one lower assembly.  Each of the two upper assemblies are identical and have steel attach links on both ends.  The lower assembly has an attachment plate secured to the upper ends of the left and right cables and an attachment link secured to the lower ends of the left and right cables.   P/N: 2089-12 (PA-12, PA-14), 2089-18 (PA-18, PA-19) NAME: MAIN LANDING GEAR SAFETY CABLES, S...
More

Seat Track Tiedowns

P/N: TDP-31 NAME: Piper Seat Track Tie Down PRICE: $87.50 / Each ELIGIBLE ON: Piper PA-31, PA31-300, PA31-325, PA31-350, PA31P-350, PA-31P, PA-31T, PA-31T1, PA-31T2, PA-31T3 STC's: No FAA-PMA'd: Yes WEIGHT: 4 Oz. MATERIAL: Aluminum anodized blue PURPOSE: To allow cargo tie down capability to any Piper style seat track. INSTALLATION: Comes in a 2 piece configuration using an AN-4 bolt to secure tie down to seat rail. MISC INFO: ...
More

Shock Struts, 3” Extended

P/N: 3164-3 (PA-18), 3164-4 (PA-12, PA-14) NAME: Shock Struts, 3'' Extended PRICE: $120.00 / Per Side STC's: Yes FAA-PMA'd: Yes MISC INFO: - P/N 3164-4: - Eligible for PA-12, -14 if PA-18 type main landing gear front fittings have been installed in accordance with STC# SA148AL, SA543AL, OR SA669AL - Powder coated black, white or, primer grey.     P/N: 3164-5 (PA-18), 3164-6 (PA-12, PA-14) NAME: Shock Struts, 6'' Ext...
More

Ski Dollies

P/N: X-1-SD NAME: Ski Dollies PRICE: $795.00 Pair ELIGIBLE ON: Only to be used on F. Atlee Dodge X-1 skis STC's: None FAA-PMA'd: None WEIGHT:  37.5lbs Per side MATERIAL:   Mild Steel and 4130N and powder coated Atlee Yellow INSTALLATION:  Slides into lower ski cross tube on ski pedestal. MISC INFO:  Ski dollies are NOT intended for aircraft taxi operations. Uses a high speed trailer wheel and tire.   Picture coming so...
More

Ski Springs

SKI SPING DOCUMENT-REFERENCE ONLY.pdf P/N: 2097 (SILVER), 2127 (GOLD) NAME: SKI SPRINGS PRICE: $165.00 / Each ELIGIBLE ON: SEE ATTACHED ""SKI SPRING DOCUMENTS"" ABOVE STC's: SA4624NM FAA-PMA'd: YES WEIGHT: - 2097: 2.4 LBS - 2127: 2.2 LBS MATERIAL: SPECIAL CADIUM PLATED STEEL PURPOSE: IMPROVES SKI RIGGING TENSION IN VERY COLD WEATHER. INSTALLATION: - WHEN INSTALLING THE AIRCRAFT SPRINGS, THE LANDING DATA IS VERY CRITICAL TO THE PER...
More

SS Front Clamp-on Shoulder Harness Attach Brackets

[PDF] FAA SHOULDER HARNESSES RECOMMENDATIONS.pdf - SOLD WITHOUT BELTS   P/N: 3232-1 NAME: Rear Clamp on Shoulder Harness Attach Brackets PRICE: $87.50 / Each ELIGIBLE ON: - J-3C, J-3F, J-3L, J-5A, J-5B, J-5C, PA-Wing Parts PA-11S, PA-Featured Products PA-12S, PA-Cessna_Fuselage PA-18 ""150"", PA-18A ""150"", PA-18S ""150"", PA-18AS ""150"",PA-18 ""105"", PA-18S ""105"", PA-18A, PA-18 ""125"", PA-18A ""125"", PA-18S ""125"", PA-18A ""135"", PA-18S ""135"",...
More

SS Rear Clamp-on Shoulder Harness Attach Brackets

[PDF] FAA SHOULDER HARNESSES RECOMMENDATIONS-2.pdf - SOLD WITHOUT BELTS P/N: 3232-2 NAME: Rear Clamp on Shoulder Harness Attach Brackets PRICE: $145.00 / Each ELIGIBLE ON: - J-3C, J-3F, J-3L, J-5A, J-5B, J-5C, PA-Wing Parts PA-11S, PA-Featured Products PA-12S, PA-Cessna_Fuselage PA-18 ""150"", PA-18A ""150"", PA-18S ""150"", PA-18AS ""150"",PA-18 ""105"", PA-18S ""105"", PA-18A, PA-18 ""125"", PA-18A ""125"", PA-18S ""125"", PA-18A ""135"", PA-18S ""135"", PA-1...
More

SS Universal Cabin Heat Box

  P/N: 18-CHB NAME: UNIVERSAL CABIN HEAT BOX PRICE: $285.00 / Each ELIGIBLE ON: PIPER AIRCRAFT STC's: NO FAA-PMA'd: NO WEIGHT: 8 OZ. MATERIAL: STAINLESS STEEL PURPOSE: - SS CABIN HEAT BOX WILL NOT CORRODE OR RUST OUT LIKE THE STOCK PIPER CABIN HEAT BOXES INSTALLATION: - CABLE ROUTING IS THE SAME AS A PIPER PA-18 SERIES AIRCRAFT - THE MOUNTING HOLES MAY NOT LINE UP WITH THE EXISTING HOLES IN THE FIREWALL MISC INFO: ...
More

STC for Fuselage Side Mounted Lower Baggage Door

[PDF] FUSELAGE SIDE MOUNTED LOWER BAGGAGE DOOR MODIFICATION.pdf P/N: 8029, Alaskan Aircraft Products NAME: STC for fuselage side mounted lower baggage door PRICE: $350.00 / STC Only ELIGIBLE ON: PA-18, PA-18 Series aircraft STC's: SA02378AK FAA-PMA'd: No WEIGHT: N/A MATERIAL: N/A PURPOSE: - This modification allows the aircraft owner to install a large lower baggage door on the right hand side of the fuselage. INSTALLATION: - This ...
More

Survival Axe

P/N: AD18-SA NAME: Survival Axe PRICE: $167.50 ELIGIBLE ON: Will fit -18 & Husky style landing gear STC's: No FAA-PMA'd: No WEIGHT: 4 Lbs MATERIAL: N/A PURPOSE: To allow aircraft owner to secure axe outside of cabin structure. INSTALLATION: - (2) Clamps, 1 on forward landing gear tube & 1 on aft landing gear tube secured with 2 ss pins - Recommended to mount on the lh gear with axe head facing forward - This survival axe i...
More

Tail Brace Beef Up

P/N: 1022-12, 1022-18 NAME: TAIL BRACE BEEF UP PRICE: $185.00 ELIGIBLE ON: WILL FIT -12, -18 AIRCRAFT STC's: NO FAA-PMA'd: NO - LOG BOOK ENTRY, MINOR ALTERATION WEIGHT: 12 OZ MATERIAL: - 4130N STEEL TUBING - POWDER COATED GREY PURPOSE: TO STRENGTHEN THE AFT TAIL SECTION TO PREVENT TAIL FROM TWISTING. INSTALLATION: - CAN BE WELDED IN OR CLAMPED IN - THE BEST TIME FOR INSTALLATION IS WHEN FABRIC IS OFF THE AIRCRAFT. MISC INFO: ...
More

Top Deck X Brace Installation, STC ONLY

[PDF] STC SA02011AK, Reference Use Only.pdf P/N: SYC Only NAME: Top Deck X Brace Installation PRICE: $265.00 / STC Only ELIGIBLE ON: Piper PA-18 Series Aircraft STC's: SA02011AK FAA-PMA'd: N/A WEIGHT: N/A MATERIAL: 4130N PURPOSE: This modification is accomplished to increase the structural strength of the top deck. INSTALLATION: This is a welding modification. Normally accomplished during the fuselage rebuilding process. MIS...
More

Top Deck X Brace Modification, STC ONLY

[PDF] STC SA02379AK, Reference Use Only.pdf P/N: STC Only NAME: Top Deck X Brace Modification PRICE: $265.00 / STC Only ELIGIBLE ON: Piper PA-12, PA-12S Series Aircraft STC's: SA02379AK FAA-PMA'd: N/A WEIGHT: N/A MATERIAL: 4130N PURPOSE: This modification strengthens upper top deck to insure and increase the structural integrity of the upper cabin. INSTALLATION: This is a weld in modification and is normally accomplished during th...
More

Under Seat Battery Rack

  P/N: 3304 NAME: Under Seat Battery Rack PRICE: $415.00 ELIGIBLE ON: PA-18 Series aircraft STC's: SA02156AK FAA-PMA'd: Yes WEIGHT: - Kit without battery: 1.2 lbs - Kit with battery: 16.4lbs. MATERIAL: - Stainless steel - Also can be fabricated using titanium per customers request (weight: .4 lbs without battery, price: $470.00) PURPOSE: - To remove the stock battery & battery box to lessen weight. Approximate weight saving: ...
More

Weld on Aft Float Fittings

[PDF] Weld On Float Fittings for PA-18 Installation.pdf P/N: 3143-12 NAME: WELD ON AFT FLOAT FITTINGS PRICE: $685.00 / Pair ELIGIBLE ON: PA-12, PA-14 STC's: SA00132SE FAA-PMA'd: YES WEIGHT: 2 LBS / Pair MATERIAL: 4130N STEEL PURPOSE: - DESIGNED TO REPLACE THE CLAMP ON STYLE FITTING AND TO PROVIDE A CLEANER STRONGER INSTALLATION. INSTALLATION: - NORMALLY ACCOMPLISHED AT TIME OF REBUILD, BUT IF FABRIC CAN BE REMOVED TO ACCOMMODATE ...
More

Weld-on Pilot Seat Belt Attach Kit

  P/N: 3246 NAME: WELD-ON PILOT SEAT BELT ATTACH KIT PRICE: $285.00 ELIGIBLE ON: PA-11, PA-18 STC's: SA02043AK FAA-PMA'd: YES WEIGHT: 12 OZ. AT FUSELAGE STATION 44 1/8 MATERIAL: 4130N TUBING & ATTACH TABS PURPOSE: - RELOCATING PILOTS SEAT BELT ATTACH TO FLOOR OF FUSELAGE. THIS PREVENTS THE PILOT SEAT FROM LEAVING THE STRUCTURE IN CASE OF AN INCIDENT. INSTALLATION: WELDING IS REQUIRED MISC INFO: - NORMALLY ACCOMPLISHE...
More

Wing Jack

P/N: AD18-WJ NAME: Wing Jack PRICE: - Without Jack:  $365..00 - With Jack:  $425.00 ELIGIBLE ON: N/A STC's: N/A FAA-PMA'd: N/A WEIGHT: N/A MATERIAL: N/A PURPOSE: - To assist in lifting a high wing aircraft less than 2500 Lbs. for the installation of aircraft skis INSTALLATION: If customer is using there jack a bushing must be welded in the lower lift bracket MISC INFO: - Always consult the aircraft owners or service manual be...
More