Brake Reinforcing Channel

  P/N: 4231 Direct replacement for P/N 12944-00 NAME: Brake Reinforcing Channel PRICE: $87.50 ELIGIBLE ON: PA-18 Series Aircraft STC's: No FAA-PMA'd: Yes WEIGHT: 0.7 Lbs. MATERIAL: - 4130N Steel - Powder coated grey PURPOSE: - This brake channel is stronger than the piper original channel and is not prone to cracking out INSTALLATION: - Same installation as stock piper channel - Normally installed during an aircraft rebuild w...
More

Cargo Net

P/N: 3234 NAME: Cargo Net PRICE: STC:$385.00 Parts Kit and Net: $785.00 ELIGIBLE ON: J3, PA-12, PA-14, PA-18 aircraft STC's: SA02452AK FAA-PMA'd: Yes WEIGHT: approx 4 LBS. MATERIAL: - Clamp in brackets: 4130N steel, powder coated flat black - Weld in brackets: 4130N steel, no paint - Net is black in color using 1'' webbing PURPOSE: - To prevent cargo from moving forward in case of heavy turbulence Or an aircraft incident. INSTAL...
More

Clamp On Headset Hanger Bracket

P/N: AD-18-HSH NAME: Clamp on headset hanger bracket PRICE: $28.50 / Each ELIGIBLE ON: PA-18 Aircraft STC's: N/A FAA-PMA'd: N/A WEIGHT: 2 Oz MATERIAL: - Steel  - Powder coated flat black PURPOSE: -To hang up headsets in cockpit INSTALLATION: - This will clamp on the top deck X-brace.  - Clamp is for 7/8'' Dia tube.  - When installing hanger post must be facing away from pilot or passanger MISC INFO: - Custom fabrication of ...
More

DHC-2 Folding Center Row Seat

  P/N: 3180 Price: $3,665 each Eligible On: DHC-2 MK.1 STC: SA4613NM FAA/PMA: Supplement 1 Purpose: To allow for a 3 person middle row bench seat. Installation: Seat snaps in using standard attach brackets. Fits into original seat bases. Must have seat belt/cargo anchors installed in floor in accordance with  STC SA3617NM.  Misc. Information: Bench can be split to allow for a single seat at times. You can order the bench with a single seat on the left or right. You c...
More

PA-12 Firewall Blanket

  P/N: AD12-FW-BLKT Price: $187.50 each Eligible On: PA-12 and PA-14 Aircraft Series STC: N/A FAA/PMA: N/A Weight: 13 oz. Material: Fabric is Naugahyde with fire block foam backing that self extinguishes and is also gas, grease, and oil resistant. Naugahyde material meets MUSS-302 flammability requirements. Foam backing meets UL-91 HF-1 flammability requirements. Fabric rated to -40 below. Purpose: Insulates firewall to reduce heat transfer and noise in the cabin. ...
More

PA-12 Instrument Panel

  P/N: 1034-00 Price: $375 each Eligible On: PA-12 STC: N/A FMA/PMA: N/A Material: 2024 T3 Aluminum Purpose: Allows standard 6 pack instrument arrangement. Installation: Bolt in, no welding required. Misc. Information: Panels are installed with quick release fasteners allowing for quick and easy access during maintenance.  
More

PA-14 Instrument Panel

  P/N: 1034-2 Price: $375 each Eligible On: PA-14 STC: N/A FAA/PMA: N/A Material: 2024 T3 Aluminum Purpose: Allows standard 6 pack instrument arrangement. Installation: Bolt on, no welding required. Misc. Information: Allows the carburetor and cabin heat controls to be moved from the cabin side wall to the instrument panel. The 6 pack panel is held in place with quick release fasteners allowing for fast and easy access during maintenance.
More

PA-18 Extended Baggage Compartment

  P/N: 2103 Price: $845 each Eligible On: PA-18 Series Aircraft STC: SA590AL FAA/PMA: Supplement 1 Weight: 7 lbs. Material: .020 2024 T3 Aluminum Purpose: Allows for more space in the baggage compartment. Extended compartment will provide approximately 4.25 cubic feet of storage space and has a weight capacity for up to 20 lbs. Installation: Shipped in knock down form. Easily assembled using supplied pop rivets. No welding required. Misc. Information: Early air...
More

PA-18 Firewall Blanket

  P/N: AD18-FW-BLKT Price: $187.50 each Eligible On: PA-18 Series Aircraft STC: N/A FAA/PMA: N/A Weight: 13 oz. Material: Fabric is Naugahyde with fire block foam backing that self extinguishes and is also gas, grease, and oil resistant. Naugahyde material meets MUSS-302 flammability requirements. Foam backing meets UL-91 HF-1 flammability requirements. Fabric rated to -40 below. Purpose: Insulates firewall to reduce heat transfer and noise in the cabin. Installat...
More

PA-18 Folding Front Seat

  P/N: 3186-1A Price: $1,785 each Eligible On: PA-18 and PA-19 Series Aircraft STC: SA02085AK FAA/PMA: Supplement 1 Material: 4130 N Purpose: Allows pilot seat to fold forward for easier loading of aircraft. Installation: Bolt in replacement for standard seat. Misc. Information: Seats are not upholstered. Contact Univair for upholstery kit information. Univair 
More

PA-18 Folding Front Seat – STC and Install Kit ONLY

  P/N: 3186-Kit or 3186-Install Price: $385 uninstalled, $845 installed Eligible On: PA-18 and PA-19 Series Aircraft STC: SA02085AK FAA/PMA: Supplement 1 Material: 4130 N Purpose: Allows existing pilot seat to be modified into a folding seat for easier loading of aircraft. Installation: Weld on modification to existing seat. Misc. Information: If you would like F. Atlee Dodge to install this kit for you, please send us your existing seat.
More

PA-18 Instrument Panel

  P/N: 1034-1 Price: $375 each Eligible On: PA-18 STC: SA143AL FAA/PMA: N/A Material: 2024 T3 Aluminum Purpose: Allows standard 6 pack instrument arrangement. Installation: Bolt on, no welding required. Misc. Information: Allows the carburetor and cabin heat controls to be moved from the cabin side wall to the instrument panel. The 6 pack panel is held in place with quick release fasteners allowing for fast and easy access during maintenance.  
More

Pilot’s Seat Bottom Access Panel

Pilot's Seat Bottom Access Panel," P/N: 3186-SLB NAME: PILOT'S SEAT BOTTOM ACCESS PANEL PRICE: $82.50 ELIGIBLE ON: AIRCRAFT USING PA-18 SEAT STC's: NO FAA-PMA'd: NO WEIGHT: 0.8 LBS. MATERIAL: - ALUMINUM - POWDER COATED FLAT BLACK PURPOSE: SEAT BOTTOM LID TO ACCESS UNDER SEAT BATTERY INSTALLATION: REQUIRES DRILLING, RIVETING MISC INFO: KIT COMES WITH HINGE AND RIVETS
More

Piper Battery Rack for Front Seat

  P/N: 3304 Price: $415 each Eligible On: PA-18 and PA-19 Series Aircraft STC: SA02156AK FAA/PMA: Supplement 1 Weight: 1.2 lb's without battery, 16.4 lb's with approved battery Material: Stainless Steel Purpose: Modification to reduce weight approximately 18.4 lb's when replacing stock rack and battery. Moves battery location to underneath the front seat in the seat base frame. Installation: Please see Installation Instructions . Install time depends upon mechanic...
More

Rear Seat Heater Kit

  P/N: 3175 Price: $735 each Eligible On: PA-18 Series Aircraft with Lycoming Engines STC: SA02094AK FAA/PMA: Supplement 4 Weight: 2.4 lbs. Material: Diverter box and push pull cables are stainless steel, hoses are 2" CEET and 2" SCAT. Purpose: The carburetor heat shroud and new cabin heat valve are utilized to provide aircraft with heating to the rear seat passenger. Installation: No welding required. Install time estimated at 8 hours. Kit can be installed at the...
More

Rear Stick Cover

  P/N: 3343 NAME: Rear Stick Cover PRICE: $335.00 ELIGIBLE ON: Will fit -3, -5, -11, -12, -18 Series aircraft STC's: No FAA-PMA'd: No WEIGHT: 1.2 LBS MATERIAL: Poly high impact plastic PURPOSE: - Prevents foreign objects from falling on rear stick stub when rear stick is removed. INSTALLATION: - Refer to installation instructions included with purchase of stick cover. - Drilling is required. - Stick cover can be installaed w...
More

Remote Compass Mounting Bracket

  P/N: 1033 Price: $175 each Eligible On: J3 thru PA-22 STC: STC SA144AL FAA/PMA: Supplement 1 Weight: Approximately 3 lbs. Material: 2024 T-3 Aluminum Purpose: To mount remote compass transmitter. Installation: Bracket attaches to the AFT side of the front spar, left hand or right hand, at approximately 140.5" outboard from the #1 inboard rib. Be sure the cable is long enough to enable the compass to be connected outside of the wing. Misc. Information: May be ...
More

Removable Rear Seat Crossbar

  P/N: 3146 Price: $335 each Eligible On: PA-18 and PA-19 Series Aircraft STC: SA681AL FAA/PMA: Supplement 1 Weight: 15 oz. Material: 4130N Square Tubing Purpose: Allows rear seat cross bar to be removed for easier loading of aircraft. Installation: No welding required, install takes about 1 hour. Misc. Info: Crossbar must be installed prior to flight to prevent serious structural failure to the fuselage side structure in the event of a hard landing or over gro...
More

Safari Seat

P/N: 6151 NAME: Safari Seat PRICE: $635.00 ELIGIBLE ON: PA-18 Series Aircraft STC's: SA02356AK-D FAA-PMA'd: Yes WEIGHT: 6.4 Lbs. MATERIAL: - Lightweight 4130N steel - Powder coated flat black PURPOSE: Saves apprpximately 14 Lbs. when removing stock seat configuration INSTALLATION: No welding required, clamp in configuration MISC INFO: - Seat bottom: 13.5'' wide - Seat back: 11.5'' wide - No upholstery included - Seat back o...
More

Seat Track Tiedowns

P/N: TDP-31 NAME: Piper Seat Track Tie Down PRICE: $87.50 / Each ELIGIBLE ON: Piper PA-31, PA31-300, PA31-325, PA31-350, PA31P-350, PA-31P, PA-31T, PA-31T1, PA-31T2, PA-31T3 STC's: No FAA-PMA'd: Yes WEIGHT: 4 Oz. MATERIAL: Aluminum anodized blue PURPOSE: To allow cargo tie down capability to any Piper style seat track. INSTALLATION: Comes in a 2 piece configuration using an AN-4 bolt to secure tie down to seat rail. MISC INFO: ...
More

SS Front Clamp-on Shoulder Harness Attach Brackets

[PDF] FAA SHOULDER HARNESSES RECOMMENDATIONS.pdf - SOLD WITHOUT BELTS   P/N: 3232-1 NAME: Rear Clamp on Shoulder Harness Attach Brackets PRICE: $87.50 / Each ELIGIBLE ON: - J-3C, J-3F, J-3L, J-5A, J-5B, J-5C, PA-Wing Parts PA-11S, PA-Featured Products PA-12S, PA-Cessna_Fuselage PA-18 ""150"", PA-18A ""150"", PA-18S ""150"", PA-18AS ""150"",PA-18 ""105"", PA-18S ""105"", PA-18A, PA-18 ""125"", PA-18A ""125"", PA-18S ""125"", PA-18A ""135"", PA-18S ""135"",...
More

SS Rear Clamp-on Shoulder Harness Attach Brackets

[PDF] FAA SHOULDER HARNESSES RECOMMENDATIONS-2.pdf - SOLD WITHOUT BELTS P/N: 3232-2 NAME: Rear Clamp on Shoulder Harness Attach Brackets PRICE: $145.00 / Each ELIGIBLE ON: - J-3C, J-3F, J-3L, J-5A, J-5B, J-5C, PA-Wing Parts PA-11S, PA-Featured Products PA-12S, PA-Cessna_Fuselage PA-18 ""150"", PA-18A ""150"", PA-18S ""150"", PA-18AS ""150"",PA-18 ""105"", PA-18S ""105"", PA-18A, PA-18 ""125"", PA-18A ""125"", PA-18S ""125"", PA-18A ""135"", PA-18S ""135"", PA-1...
More

Weld-on Pilot Seat Belt Attach Kit

  P/N: 3246 NAME: WELD-ON PILOT SEAT BELT ATTACH KIT PRICE: $335.00 ELIGIBLE ON: PA-11, PA-18 STC's: SA02043AK FAA-PMA'd: YES WEIGHT: 12 OZ. AT FUSELAGE STATION 44 1/8 MATERIAL: 4130N TUBING & ATTACH TABS PURPOSE: - RELOCATING PILOTS SEAT BELT ATTACH TO FLOOR OF FUSELAGE. THIS PREVENTS THE PILOT SEAT FROM LEAVING THE STRUCTURE IN CASE OF AN INCIDENT. INSTALLATION: WELDING IS REQUIRED MISC INFO: - NORMALLY ACCOMPLISHE...
More